Email us: info@yacht-supply24.com or fill our Feedback form.
You can also fill out the "Ask a question" form on the right or at the bottom of the page.
|
1-2 weeks delivery time Introducing the Yacht Devices IP67USBMALE: an IP67-rated USB cable featuring Type-A Male connectors on both ends, designed for direct connection between USB Type-A ports. Perfectly suited for the YDNU-02 USB Gateway. |
$ 45.41
-
+
|
|
1-2 weeks delivery time The Yacht Devices SmartCraft 10-Pin Engine Gateway Adaptor Cable is designed to connect compatible Mercury and MerCruiser SmartCraft engines to the YDEG-04 Engine Gateway through the 10-pin SmartCraft port. The plug-and-play adaptor enables supported engine information to be displayed on NMEA 2000 instruments, including engine speed, engine hours, engine temperature, boost pressure, keyswitch battery voltage, fuel rate, fuel tank level and engine warnings transmitted in J1939 messages with PGN 65226. |
$ 57.05
-
+
|
|
1-2 weeks delivery time Yacht Devices USBMALE - USB Cable Type-A Male-to-Male is a high-quality USB cable with Type-A Male connectors on both ends. It allows for a direct connection between two USB Type-A ports and is designed for use with the YDNU-02 USB Gateway. With a length of 1.2m (3.9 ft), it provides flexibility and efficient data transfer. |
$ 22.13
-
+
|
|
1-2 weeks delivery time The Yacht Devices YAN-4JH is an Engine Gateway adaptor cable designed to connect compatible Yanmar 4JH engines to the YDEG-04 Engine Gateway and create a Yanmar-to-NMEA 2000 interface. Through the gateway, supported engine data can be displayed on NMEA 2000 instruments, including engine speed, engine hours, engine temperature, boost pressure, keyswitch battery voltage, fuel rate, fuel tank level and engine warnings transmitted in J1939 messages with PGN 65226. The adaptor is intended for engine CAN integration and plug-and-play installation. |
$ 45.41
-
+
|
|
1-2 weeks delivery time The Yacht Devices YAN-B25 is a specialized adaptor cable designed to connect the YDEG-04 Engine Gateway to Yanmar engines equipped with a B25 or C35 engine panel. It provides the physical connection required for communication and data transfer between the engine gateway and the compatible Yanmar engine panel system. |
$ 57.05
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDAB-01N is a multifunctional NMEA 2000 alarm and control device with an NMEA 2000 Micro Male connector, supplied external 16 mm push button with integrated LED, and output for a 4–8 Ohm speaker. It integrates a 10 W audio amplifier and 28 built-in sound signals and can operate as an MOB button, 28-channel digital switching alarm unit or engine monitoring alarm. The device operates from 7–16 V supplied by the NMEA 2000 network, measures 54 mm in case length, has a 400 mm cable and weighs 37 g; the speaker is not supplied. The three operating modes and MOB, digital switching and engine-monitoring functions are documented by the manufacturer. |
$ 220.04
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDAB-01R is a multifunctional NMEA 2000 alarm and monitoring unit equipped with a SeaTalk NG-compatible connector, an external 16 mm push button with integrated LED, and an output for a standard 4–8 Ohm speaker. It features a built-in 10 W audio amplifier, 28 sound signals and three configurable operating modes: MOB button, 28-channel digital switching alarm unit and engine monitoring unit. The device operates from 7–16 V via the NMEA 2000 network, weighs 37 g, has a 54 mm case length and a 400 mm cable; the speaker is not supplied. |
$ 220.04
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDAP-04N is a compact NMEA 2000 autopilot course computer and actuator control unit designed for rudder-equipped vessels up to 12 tonnes displacement. It supports AUTO, WIND and TRACK operating modes and can control a compatible rudder drive and clutch with a 7–29 V drive/clutch circuit, up to 10 A continuous and 16 A peak motor current, and up to 10 A clutch current. The NMEA 2000 interface operates from 7–16 V and consumes up to 20 mA; the unit provides 2500 VRMS galvanic isolation between NMEA 2000 and other interfaces. |
$ 406.31
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDBC-05N is a compact digital barometer for NMEA 2000 networks, designed to measure atmospheric pressure from 300 to 1100 hPa and provide the data directly to compatible chart plotters and navigation displays. It offers 0.01 hPa output resolution, ±0.12 hPa relative accuracy and ±1 hPa absolute accuracy from 0°C to +65°C, while operating from 7–16 V with 24 mA current consumption. The YDBC-05N version uses an NMEA 2000 Micro Male connector and weighs just 11 g. |
$ 173.47
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDBC-05NT is a compact digital barometer for NMEA 2000 networks with an integrated 120 Ohm terminator, allowing the device to be installed in place of an existing network terminator. It measures atmospheric pressure from 300 to 1100 hPa with 0.01 hPa output resolution, ±0.12 hPa relative accuracy and ±1 hPa absolute accuracy from 0°C to +65°C. The unit operates from 7–16 V, consumes 24 mA, weighs 11 g and uses an NMEA 2000 Micro Male connection compatible with DeviceNet Micro Male and Garmin NMEA 2000 Male. |
$ 173.47
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDBC-05R is a compact digital barometer designed for SeaTalk NG and NMEA 2000-based marine networks, providing atmospheric pressure data directly to compatible chart plotters and navigation displays. It measures from 300 to 1100 hPa with 0.01 hPa output resolution, ±0.12 hPa relative accuracy and ±1 hPa absolute accuracy from 0°C to +65°C. The device operates from 7–16 V, consumes 24 mA, weighs 11 g and uses a Raymarine SeaTalk NG Female connector. |
$ 173.47
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDBC-05RT is a compact SeaTalk NG digital barometer with an integrated 120 Ohm network terminator, designed to replace an existing terminator at the end of an NMEA 2000/SeaTalk NG backbone. It measures atmospheric pressure from 300 to 1100 hPa with 0.01 hPa resolution, ±0.12 hPa relative accuracy and ±1 hPa absolute accuracy from 0°C to +65°C. The unit measures approximately 54 × 20 × 20 mm, weighs 11 g, operates from 7–16 V and consumes 24 mA, while pressure data can be displayed as numerical values, graphs or trend indicators on compatible navigation instruments. |
Our managers will contact you and clarify the terms of the order
|
|
1-2 weeks delivery time The Yacht Devices YDBM-01N is an NMEA 2000 battery and DC circuit monitor with an NMEA 2000 Micro Male connector, designed to measure voltage and bidirectional current and provide calculated battery data such as state of charge, consumed ampere-hours, time remaining and state of health. It supports external shunts rated from 5 to 2500 A, with a recommended nominal drop of 75 mV, provides ±0.5% current measurement accuracy and 0.1 V voltage measurement accuracy, and accepts up to 40 V DC on its measurement inputs. The unit operates from 7–16 V via NMEA 2000, consumes 50 mA on average, measures 54 mm in case length and weighs 60 g. |
$ 220.04
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDBM-01R is a marine battery and DC circuit monitor with a Raymarine SeaTalk NG-compatible network connector, designed to measure voltage and bidirectional current and report both measured and calculated battery data to NMEA 2000 equipment. It supports external shunts rated from 5 to 2500 A with a recommended 75 mV nominal drop, provides ±0.5% current measurement accuracy and 0.1 V voltage measurement accuracy, accepts up to 40 V DC on its inputs, and provides 2500 VRMS isolation between the NMEA 2000 interface and measurement inputs. The unit operates from 7–16 V, consumes 50 mA on average, measures 54 mm in case length and weighs 60 g. |
$ 220.04
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDBM-02N is an NMEA 2000 battery and DC circuit monitor designed to measure voltage and bidirectional current and report calculated battery status data such as state of charge and health to the vessel network. Compared with the previous YDBM-01 model, the YDBM-02 adds an extra wire and supports installation with the external shunt connected to either the positive or negative battery terminal. It supports shunts rated from 5 to 2500 A with a recommended 75 mV nominal drop, provides ±0.5% current measurement accuracy and 0.1 V voltage measurement accuracy, accepts up to 40 V DC on its inputs and provides 2500 VRMS isolation between the NMEA 2000 interface and measurement inputs. |
$ 220.04
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDBM-02R is a marine battery and DC circuit monitor with a Raymarine SeaTalk NG-compatible connector for direct integration into SeaTalk NG networks. It measures voltage and bidirectional current, supports calculated State of Charge, State of Health, consumed ampere-hours and time remaining, and can work with an external shunt installed on either the positive or negative battery terminal. The unit supports shunts rated from 5 to 2500 A with a recommended 75 mV nominal drop, provides ±0.5% FSR current measurement accuracy and 0.1 V voltage measurement accuracy, operates from 7–16 V, measures 54 mm in case length and weighs 60 g. |
$ 220.04
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDEG-04N is a compact NMEA 2000 Engine Gateway with an NMEA 2000 Micro Male connector, designed to interface compatible Volvo Penta, J1939, SmartCraft and BRP CAN engine networks with marine NMEA 2000 electronics. It operates from 10–16 V on the NMEA 2000 side, draws 38 mA on average, accepts 10–30 V from the engine network side, provides 2500 VRMS galvanic isolation between NMEA 2000 and the engine network, and supports up to 8 engines, 8 transmissions, 8 batteries and 10 fuel tanks depending on protocol and configuration. The unit has a 500 mm engine cable, 54 mm case length and 75 g weight, with MicroSD-based configuration, firmware updates and engine-network data logging. |
$ 289.89
-
+
|
|
1-2 weeks delivery time The Yacht Devices YDEG-04R is a SeaTalk NG-compatible Engine Gateway designed to interface supported Volvo Penta, J1939, SmartCraft and BRP CAN engine networks with NMEA 2000 marine electronics. It operates from 10–16 V on the NMEA 2000 side, draws 38 mA on average, accepts 10–30 V from the engine network side, provides 2500 VRMS galvanic isolation between NMEA 2000 and the engine network, and has a 500 mm engine cable, 54 mm case length and 75 g weight. Depending on protocol and configuration, the gateway can transfer engine, transmission, battery and fuel data to compatible chart plotters and supports up to 8 engines on a joined network. |
$ 289.89
-
+
|
What are the primary functions of Yacht Devices marine electronics?
Yacht Devices marine electronics primarily function to integrate various onboard systems using NMEA 2000 and NMEA 0183 protocols. The Engine Gateway YDEG-04, for example, allows engines to connect to the NMEA 2000 marine electronics network, providing data such as engine revolutions, fuel rate, and fluid levels to chart plotters and instrumental displays. These devices are compatible with equipment from many brands and they support bi-directional communication, enabling seamless data exchange and system control across the entire marine digital network. Yacht Devices, established as a leader since 2015, focuses on NMEA-2000 marine electronics, adhering to standards set by the National Marine Electronics Association. Their products, such as the NMEA 0183 gateway, allow you to connect NMEA 0183 equipment to a NMEA 2000 network and vice versa, ensuring versatile integration. The gateway YDWG-02 and other devices like the Garmin NMEA 2000 and Simrad offer broad compatibility. They allow users to see and manage data on chart plotters and PC screens, update firmware, and handle various navigation data, including AIS messages from vessels and aircraft. These gateways also support engines with a J1939 serial interface, enabling monitoring of fluid levels on NMEA 2000 devices. Yacht Devices' electronics, such as the bi-directional converter, provide wide support for message types, ensuring comprehensive system integration and control.
What role does a NMEA 0183 multiplexer play in a yacht's electronic system?
A NMEA 0183 multiplexer plays a crucial role in a yacht's electronic system by allowing multiple NMEA 0183 data sources, such as GPS, AIS, and depth sounders, to be combined and transmitted through a single output. This ensures seamless integration and communication between various marine devices and the yacht's navigation system. Additionally, it can interface with NMEA 2000 networks via a gateway, enhancing the overall efficiency and functionality of the yacht's electronics.
What role does the Seatalk adapter play in connecting Raymarine devices to NMEA 2000 networks?
The Seatalk adapter plays a crucial role in connecting Raymarine devices to NMEA 2000 networks by acting as a bridge between the proprietary Seatalk protocol and the standardized NMEA 2000 marine digital network. This adapter allows you to see data from a NMEA 2000 network on Raymarine devices and vice versa, ensuring seamless integration and communication. It is equipped with NMEA 2000 functionality, enabling yacht owners to connect 0183 equipment to a NMEA 2000 network and providing a reliable interface to manage engine data, fluid levels, and other navigation information. For robust and trusted marine data interfaces, explore Actisense, a leading brand in marine electronics integration.
How does a Yacht Devices NMEA 2000 Wi-Fi gateway help monitor boat navigation data on smartphones and tablets?
A Yacht Devices NMEA 2000 Wi-Fi gateway helps monitor boat navigation data by connecting to the vessel's digital backbone and accessing live data streams, creating a local wireless network for personal devices, converting proprietary NMEA 2000 PGNs into universal Wi-Fi protocols, feeding data into compatible navigation apps such as Navionics and iNavX, and allowing several tablets or phones to display synchronized real-time data on a multi-screen dashboard.
What is the purpose of an engine gateway YDEG-04 for Volvo Penta and other J1939 engines in a NMEA 2000 marine network?
Think of the YDEG-04 as your engine's personal interpreter on a modern boat. It listens to the specialized digital chatter from J1939 engines to NMEA 2000, like your Volvo Penta or Mercury, and translates every detail into a common language. This gateway allows you to see real-time vitals—from RPM to coolant temperature—right on your chartplotter screen or sleek web gauges. Ultimately, it bridges the gap, weaving your propulsion data seamlessly into the boat's central digital network on a PC for smarter oversight.
How do Yacht Devices USB and Wi-Fi gateways differ when connecting NMEA 2000 marine electronics to a PC or laptop?
The USB gateway offers a simple, plug-and-play wired link, perfect for a stable connection at the nav station to log NMEA 2000 data. Conversely, the NMEA 2000 Wi-Fi gateway acts as a wifi server, creating a local wifi network that broadcasts data wirelessly to tablets and phones. Key distinctions include: Link Type - a physical cable versus a versatile Wi-Fi network; Device Access - single-computer use versus multi-crew access via apps like Aqua Map; Data Protocol - direct stream versus network broadcast using UDP or TCP protocols.
What role does a Seatalk NG to NMEA 2000 converter play when integrating Raymarine Seatalk NG equipment with other onboard systems?
This compact device is the essential peacemaker for a mixed-brand electronics suite. It allows your Raymarine Seatalk NG gear, such as an autopilot, to communicate freely with devices from Furuno or Simrad Simnet on the same backbone. Without it, critical data like GPS position or water depth remains trapped within brand-specific silos. The converter ensures all your instruments share network data cohesively, creating a unified situational picture.
How can Yacht Devices digital switching and switch control modules simplify AC and DC monitoring on a boat?
These modules transform traditional, manual electrical panels into intelligent, networked systems. The NMEA 2000 digital switching replaces physical switches with solid-state circuit control, managed from a screen. This provides remote operation and real-time status of lights, bilge pumps, and outlets; switch control allows viewing precise current draw for each circuit, aiding in load management; and the capability to program automated sequences for anchoring or docking.
What should be considered when configuring a Yacht Devices NMEA 2000 router or Wi-Fi router in a marine electronics network?
Setting up these devices focuses on creating a reliable and secure data highway. For a Wi-Fi router (YDWG), choosing an unused channel prevents interference, and securing your Wi-Fi network keeps your NMEA data private. You must match the device's output settings (like UDP/TCP) to the input requirements of your navigation apps to ensure they receive the network data flawlessly. Consider physical placement for best signal strength and use a dedicated drop cable for clean power to avoid glitches in your connected devices.