BEP Marine offers a comprehensive range of marine electrical products, including battery switches, VSR (Voltage Sensitive Relays), switch panels, and remote-operated battery switches. These products are designed to enhance the electrical systems of boats and yachts. The BEP Marine battery switch allows users to control power distribution, isolate batteries, and prevent electrical drain when the vessel is not in use. VSRs facilitate automatic charging and isolation of multiple battery banks, ensuring optimal battery health. The BEP Marine switch panels provide organized control for various onboard systems. These products collectively contribute to efficient energy management and improved safety on marine vessels.
|
1-2 weeks delivery time The BEP 715-H is a pre-assembled battery distribution cluster for single-engine installations using two dedicated battery banks. This unit is the horizontal version of the system (Part # 715-H) and is intended for setups including single outboard dual battery bank, single alternator dual battery bank, or twin alternator dual battery bank, providing a clean and organized battery management solution.
|
$ 177.06
-
+
| ||
|
1-2 weeks delivery time The BEP 715-S is a horizontal battery distribution cluster designed for twin inboard or outboard engines with 2 battery banks. This configuration operates without DVSR, and allows house loads to be switched between port and starboard batteries. The selector switch can also be used to parallel both batteries when set to both positions. Dimensions: 8.1" × 2.75" × 3" (210 × 69 × 75 mm).
|
$ 223.40
-
+
| ||
|
BEP 714-140A-DVSR-B – Battery Distribution Cluster for Single Engine with 2 Battery Banks, with DVSR
1-2 weeks delivery time The BEP 714-140A-DVSR-B is a battery distribution cluster for single inboard or outboard engines with 2 battery banks, supplied with a dual sensing DVSR (710-140A) to automatically manage charging and isolation between banks. Orientation: vertical. Dimensions: 5.4" x 2.75" x 3" (138 x 69 x 75 mm).
|
$ 170.82
-
+
| ||
|
BEP 716-H-140A-DVSR – Dual Battery Charging Cluster, Horizontal, for Single Engine / 2 Battery Banks
1-2 weeks delivery time The BEP 716-H-140A-DVSR is a horizontal dual battery charging cluster for single inboard or outboard engines with two battery banks, designed as a direct replacement for a traditional battery selector switch with no additional wiring required. It supports DVSR operation, with 125A continuous DVSR charging current and a 275A continuous battery switch rating, providing an automatic battery management solution and replacing battery isolator systems.
|
$ 368.68
-
+
| ||
|
1-2 weeks delivery time The BEP 716-SQ-140A-DVSR is a square dual battery charging cluster for single inboard or outboard engines with two battery banks, designed as a replacement for a traditional battery selector switch with no extra wiring required. It includes DVSR operation for automatic battery management, with 125A continuous DVSR charging current and a 275A continuous battery switch rating, and it replaces battery isolator systems to help prevent flat start batteries.
|
$ 321.21
-
+
| ||
|
1-2 weeks delivery time The BEP 716-SQ-140A-DVSR-B is a square battery distribution and charging cluster designed for single engine systems with two battery banks, providing automatic battery management via DVSR operation. It is intended as a replacement for a traditional battery selector switch setup, supporting 125A continuous DVSR charging current and a 275A continuous battery switch rating for reliable dual-bank power management.
|
$ 364.60
-
+
| ||
|
1-2 weeks delivery time The BEP 716-V-140A-DVSR is a vertical dual battery charging cluster for single inboard or outboard engines with two battery banks, designed to replace a traditional battery selector switch by connecting existing wiring to the 716 cluster with no extra wires required. It supports DVSR operation, providing automatic battery management with 125A continuous DVSR charging current and a 275A continuous battery switch rating, and it replaces battery isolator systems to help prevent flat start batteries.
|
$ 357.40
-
+
| ||
|
1-2 weeks delivery time The BEP 717-140A-DVSR is a horizontal battery charging and distribution cluster for twin outboard engine installations with three battery banks, featuring DVSR operation for automatic battery management. It supports 125A continuous DVSR charging current and has a 275A continuous battery switch rating, providing a compact solution for managing multi-bank battery systems.
|
$ 654.36
-
+
| ||
|
1-2 weeks delivery time The BEP 718-140A-DVSR is a horizontal battery charging and distribution cluster for twin inboard engine systems with three battery banks, featuring DVSR operation for automatic battery management. It supports 125A continuous DVSR charging current and a 275A continuous battery switch rating, providing a compact solution for managing multi-bank battery systems onboard.
|
$ 401.55
-
+
| ||
|
1-2 weeks delivery time The BEP 719-140A-DVSR is a square battery charging and distribution cluster designed for triple outboard engine installations with four battery banks, using multiple DVSRs to provide combined charging from all three engines into the house battery. It supports 125A continuous DVSR charging current and features a 275A continuous battery switch rating, delivering automatic multi-bank battery management for complex outboard setups.
|
$ 881.41
-
+
| ||
|
1-2 weeks delivery time The BEP 720 is a heavy-duty On/Off battery switch designed for larger vessels and high electrical loads, rated at 600A continuous, 800A intermittent (5 min) and 2500A cranking (10 sec) at 48V DC. It features tin-plated copper studs & nuts, is ignition-protected, supports rear panel or surface mounting, and uses a proven self-cleaning sliding copper contact design for reliable circuit isolation.
|
$ 145.94
-
+
| ||
|
1-2 weeks delivery time The BEP 720-DP is a heavy-duty double pole battery switch for high-load installations, rated at 400A continuous, 525A intermittent (5 min) and 1500A cranking (10 sec) at 48V DC. It features On/Off/DP operation, ignition-protected construction, tin-plated copper studs & nuts, and uses 2 x 1/2" (12mm) studs with recommended cabling of 2x 3/0 / 2x 95mm².
|
$ 243.05
-
+
| ||
|
1-2 weeks delivery time The BEP 720-DP/B is a heavy-duty double pole battery switch designed for marine battery systems, rated for 48V DC with 400A continuous, 525A intermittent (5 min) and 1500A cranking (10 sec) performance. It features On/Off/DP operation, ignition-protected construction, tin-plated copper studs & nuts, and uses 2 x 1/2" (12mm) studs for high-current cabling installations.
|
$ 240.56
-
+
| ||
|
1-2 weeks delivery time The BEP 720-MDO is a motor-driven remote operated battery switch with an optical sensor, designed to mount close to the battery to reduce cable lengths and improve installation efficiency. Rated at 500A continuous, 700A intermittent (5 min) and 2500A cranking (10 sec), it operates on 9.5–32V DC and supports remote isolation for high-load circuits such as bow and stern thrusters, with low standby current draw (<5mA) and the ability to switch different voltage circuits.
|
$ 420.90
-
+
| ||
|
1-2 weeks delivery time The BEP 720-MDO-EP is a remotely activated emergency parallel switch for 12V/24V systems (both battery banks must be the same voltage), providing a high-current emergency parallel connection operated via a dash-mounted momentary button. It enables a 10-minute emergency parallel function (no voltage sensitive function) and includes manual override, with a 500A rating and recommended cabling of 2x 3/0 AWG (95mm²) for demanding marine installations.
|
$ 472.07
-
+
| ||
|
1-2 weeks delivery time The BEP 720-MDVSO is a dual operation voltage sensitive switch (VSS) for 12V/24V systems (both battery banks must be the same voltage), providing dual battery sensing and automatic combine/isolate control based on the presence of a charging source such as an alternator or battery charger. It also includes a remote emergency parallel function operated by a momentary dash button to parallel batteries for 10 minutes, with manual override, low power consumption (<6mA), and a 500A rating, designed for long-term marine use with ignition-protected construction.
|
$ 374.04
-
+
| ||
|
1-2 weeks delivery time The BEP 720B is a heavy-duty On/Off battery switch for high electrical loads, rated for 48V DC with 600A continuous, 800A intermittent (5 min) and 2500A cranking (10 sec) capability. It features ignition-protected construction with tin-plated copper studs & nuts, 2 x 1/2" (12mm) studs, and supports recessed or surface mounting for reliable battery isolation in demanding marine installations.
|
$ 127.76
-
+
| ||
|
1-2 weeks delivery time The BEP 720MDVSO-KEY-B is a key-operated control switch designed for use with the BEP 720-MDVSO Dual Operation VSS (Voltage Sensitive Switch) system. It provides a secure way to enable/disable VSS control functions and is intended as an accessory control component rather than a full high-current battery isolation switch.
|
$ 15.44
-
+
| ||
|
1-2 weeks delivery time The BEP 721 is a heavy-duty battery selector switch for high-load installations, providing 1-2-Both-Off battery bank selection and rated for 48V DC with 350A continuous, 500A intermittent (5 min) and 1500A cranking (10 sec) performance. Built in the same module as the BEP 720, it supports recessed or surface mounting, uses tin-plated copper studs & nuts, is ignition-protected, and is designed for reliable manual battery bank control.
|
$ 158.95
-
+
| ||
|
1-2 weeks delivery time The BEP 721B is a heavy-duty battery selector switch for 48V DC systems, providing 1-2-Both-Off battery bank selection for reliable manual power management. It is rated at 350A continuous, 500A intermittent (5 min) and 1500A cranking (10 sec), features ignition-protected construction with tin-plated copper studs & nuts, and supports recessed or surface mounting in demanding marine electrical installations.
|
$ 126.24
-
+
| ||
What is the function of a BEP Marine battery switch and how does it contribute to efficient power management on boats and yachts?
A BEP Marine battery switch serves as a vital component for power management on boats and yachts. It allows users to control the connection between the battery and onboard systems, helping to prevent unnecessary battery drain during periods of inactivity. This contributes to efficient power utilization, extends battery life, and enhances safety. The BEP Marine Battery Switch, in conjunction with other products like VSRs (Voltage Sensitive Relays) and switch panels, provides boat owners with the ability to manage and distribute power effectively, ensuring optimal performance of electrical systems while maintaining a reliable power supply for various onboard equipment.
How does a BEP Marine VSR (Voltage Sensitive Relay) enhance battery charging and maintenance across multiple battery banks?
A BEP Marine VSR (Voltage Sensitive Relay) plays a crucial role in optimizing battery charging and maintenance across multiple battery banks on boats and yachts. This intelligent relay automatically detects the voltage levels of different battery banks and connects them for charging when the main engine is running or an external charging source is active. This enhances battery performance and extends their lifespan by ensuring that all batteries receive an appropriate charge without overloading or undercharging, thereby contributing to efficient energy distribution and reliable power supply on marine vessels.
For secure installation and durable storage, pair this kit with a reliable Marine Battery Box.
In what scenarios is the BEP Marine 701 MD commonly utilized, and what specific features does it offer for marine applications?
The BEP Marine 701 MD is commonly employed in scenarios requiring reliable battery monitoring and management on boats and yachts. This advanced module offers features like voltage, current, and temperature sensing, making it a valuable tool for assessing battery health and performance. It aids in preventing battery overdischarge and overheating, ensuring optimal battery conditions and contributing to safer and more efficient marine operations.