Since its inception in 1899, BUKH has been manufacturing marine engines. With over a century of experience, these engines have evolved to become some of the most reliable in the world.
Fast deliveries of yacht equipment, calculation, selection of analogues and spare parts. Send us your request and we will contact you ASAP with a solution. We deliver in Cyprus, throughout Europe and worldwide. More than 10 years of experience.
Email us: info@yacht-supply24.com or fill our Feedback form.
You can also fill out the "Ask a question" form on the right or at the bottom of the page.
|
1-2 weeks delivery time The Bukh 000E5360 exhaust sealing gasket is designed to secure a tight, leak-resistant joint in the exhaust system on BUKH DV36 and DV48 marine diesel engines. Used at the exhaust manifold connection and within the air inlet and turbocharger assembly on DV48 applications, it helps maintain correct exhaust flow, protects surrounding components from hot gas leakage, and supports dependable engine performance. |
$ 18.48
-
+
|
|
1-2 weeks delivery time The Bukh 000E5421 governor shaft is a precision engine shaft used in the governor and regulating handle system on BUKH DV24RME, DV29RME, and DV32 marine diesel engines, supporting accurate speed control and stable throttle response. This same shaft is also applied within the DV24RME camshaft and lubricating oil pump and filter assembly, helping keep key mechanical drives aligned and operating smoothly. |
$ 255.51
-
+
|
|
1-2 weeks delivery time The Bukh 000E5422 nylon friction disc is a plastic bushing-style element for the governor shaft used on BUKH DV24RME, DV29RME, and DV32 marine engines. Installed within the governor and regulating handle assembly, it helps provide controlled friction for stable, precise throttle and speed adjustment; it is also used on DV24RME applications within the camshaft and lubricating oil pump and lubricating oil filter assembly. |
$ 57.08
-
+
|
|
1-2 weeks delivery time The Bukh 000E5685 undersize main bearing liner set is a 0.6 mm main bearing solution for BUKH DV36 and DV48 engines, intended for the crankshaft main bearing positions within the crankshaft and bearing assembly. Supplied as two matching shells (one smooth, one with an oil groove and oil feed hole), it supports stable crankshaft alignment and reliable oil distribution under marine operating loads. |
$ 285.76
-
+
|
|
1-2 weeks delivery time The Bukh 000E5827 rifle bushing is a precision support component used to locate and stabilize mating parts in Bukh marine engine assemblies. As a replacement bushing, it helps maintain correct alignment, promotes smooth operation, and reduces wear in the surrounding components during continuous marine duty. |
$ 467.18
-
+
|
|
1-2 weeks delivery time The Bukh 000E5829 sacrificial zinc anode is a saildrive corrosion-protection component for BUKH DV10SME and DV48SME marine diesel installations. Designed to be consumed in service, it helps shield underwater saildrive metal components from galvanic attack, supporting longer service life and dependable operation in harsh seawater environments. |
$ 170.26
-
+
|
|
1-2 weeks delivery time The Bukh 000E6018 oil pipe is a dedicated oil-line component used in the oil sump and bilge pump pipework on BUKH DV36 and DV48 marine diesel engines. Installed at the rear-end assembly area around the rotating weight and fuel lift pump, it supports correct oil routing within the engine’s lubrication system for dependable operation. |
$ 357.64
-
+
|
|
1-2 weeks delivery time The Bukh 000E6036 rubber coupling element is a flexible clutch and coupling component used in the drivetrain interface on multiple BUKH marine diesel engines. Installed in the reversing gear mounting (M 60) on DV24RME, DV29RME, and DV32 engines, and at the rear-end rotating weight and fuel lift pump drive on DV36 and DV48 engines, it helps cushion torsional shocks and supports smoother power transmission. |
$ 165.86
-
+
|
|
1-2 weeks delivery time The Bukh 000E6037 crankshaft-side flexible coupling half with cone provides a secure, aligned connection for reversing gear installation on BUKH DV-series marine diesel engines. Designed for the M60 reversing gear mounting arrangement, it helps transmit torque smoothly while the flexible coupling design supports quieter, more controlled drivetrain operation on DV24RME, DV29RME, and DV32 applications. |
$ 249.92
-
+
|
|
1-2 weeks delivery time The Bukh 000E6039 flexible coupling half with cone (D 30) is a driveline coupling component used at the rear-end rotating weight and fuel lift pump assembly on BUKH DV36 and DV48 marine diesel engines. Designed to support secure, accurate connection in the coupling arrangement, it helps maintain smooth power transmission and dependable operation in the rear-end drive area. |
$ 249.92
-
+
|
|
1-2 weeks delivery time The Bukh 000E6156 thermostat housing cap is a dedicated cover for the thermostat location in the keel cooling system on BUKH DV36 and DV48 marine diesel engines. It helps secure and protect the thermostat housing area to support stable coolant temperature control and dependable engine operation underway. |
$ 545.60
-
+
|
|
1-2 weeks delivery time The Bukh 000E6168 angled hose connector elbow is a circulation-pump hose fitting designed for BUKH DV36 and DV48 marine diesel engines. Installed on the circulation pump, it provides a secure angled connection for the cooling hose run, supporting tidy hose routing and dependable coolant flow through the engine’s cooling circuit. |
$ 205.71
-
+
|
|
1-2 weeks delivery time The Bukh 000E6250 thermostat for keel-cooled systems regulates coolant temperature on BUKH DV36 and DV48 marine diesel engines. By controlling coolant flow through the keel cooling circuit as the engine warms up, it helps the engine reach and maintain the correct operating temperature for dependable performance underway. |
$ 245.86
-
+
|
|
1-2 weeks delivery time The Bukh 000E6252 water pump gear wheel is a precision drive gear used in the cooling water pump system on BUKH DV36 and DV48 marine diesel engines. Installed with the circulation pump and also referenced in the rear-end rotating weight and fuel lift pump assembly, it helps transmit drive to the pump for steady coolant circulation and dependable engine temperature control. |
$ 1,244.71
-
+
|
|
1-2 weeks delivery time The Bukh 000E6302 tension clamp secures the tension device hardware used around the injection pump and oil cooler on BUKH DV36 and DV48 marine diesel engines. Designed for a dependable hold in a high-vibration engine space, it helps keep the assembly firmly retained for stable operation underway. |
$ 76.35
-
+
|
|
1-2 weeks delivery time The Bukh 000E6339 cylinder head gasket is a critical sealing element for the cylinder head joint on BUKH DV8 and DV10LSME marine diesel engines. It helps maintain proper compression and separates combustion gases from coolant and oil passages, supporting reliable operation and protecting the engine during continuous marine duty. |
$ 102.05
-
+
|
|
1-2 weeks delivery time The Bukh 000E6355 fitting set for the oil bilge pump supports secure connections in the oil bilge pump installation on BUKH DV36 and DV48 engines. Used at the rear-end rotating weight and fuel lift pump area, these fittings help route and seal oil bilge pump lines for clean, dependable operation in marine engine service. |
$ 87.58
-
+
|
|
1-2 weeks delivery time The Bukh 000E6364 reducing nipple is a compact connection fitting used in the air inlet and turbocharger assembly on BUKH DV48 marine diesel engines. It supports a secure, correctly stepped interface between connected components, helping maintain a tight, dependable air path for stable engine breathing and turbocharger performance. |
$ 92.40
-
+
|
What are the key features of BUKH marine diesel engines that make them suitable for lifeboats?
BUKH marine diesel engines are specifically designed for lifeboats, ensuring reliability and compliance with SOLAS marine safety standards. Their compact, lightweight design and ability to start manually or with minimal power make them ideal for emergency situations. Additionally, these engines are built to endure harsh marine environments, providing smooth operation and minimal vibration for both commercial and leisure applications.
How does BUKH ensure its diesel motors meet international marine safety standards?
BUKH ensures its diesel motors meet international marine safety standards by designing and manufacturing engines in compliance with stringent SOLAS requirements. These compact, lightweight diesel engines are engineered in Denmark with a focus on reliability and durability, making them suitable for both commercial and leisure applications. The company's reputation for quality is reinforced through genuine parts, meticulous service systems, and thorough testing to meet the needs of operators and owners worldwide.
How does the water cooling system in BUKH engines contribute to their efficiency and reliability?
The water cooling system in BUKH engines enhances efficiency and reliability by maintaining optimal operating temperatures during extended use. This system ensures the compact lightweight diesel engine runs smoothly, even under demanding conditions, by dissipating heat effectively. Designed to suit all commercial and leisure applications, it reduces wear on internal components and supports consistent performance for work boats and inboard setups.
What does SOLAS marine approval mean for BUKH diesel engines used in lifeboats and rescue boats?
SOLAS approval for BUKH engines confirms they meet the strictest global standards for maritime safety. This certification is a fundamental requirement for powering marine safety equipment on merchant vessels. It provides absolute confidence that these diesels will start and perform under the most severe emergency conditions at sea.
How are models like the BUKH DV10, DV24, and DV36 designed to be among the most reliable diesel engines in the world?
Reliability stems from a philosophy of robust simplicity, honed over decades as one of the world's leading OEM manufacturers of marine diesel engines for lifeboats. Key design principles include: over-engineered, low-stress internal components; minimalistic systems with fewer potential failure points; use of corrosion-resistant materials for longevity.
What are the advantages of a keel-cooled BUKH engine compared to a conventional raw-water cooled system?
Keel-cooled BUKH engines use a closed, internal coolant loop that shields the system from silt, salt, and debris, resulting in drastically reduced corrosion and abrasion. Maintenance focuses on the external keel exchanger, making them ideal for shallow, muddy, or high-salinity waters with simplified cold weather readiness using standard antifreeze. In contrast, raw-water cooled systems constantly ingest surrounding water, leading to elevated wear on pumps and passages, demanding frequent strainer and impeller care, and requiring thorough drainage to prevent freeze damage.
How does the 20hp and 24hp power range of BUKH engines match typical lifeboat and workboat requirements?
The DV20 and 24 hp outputs deliver the ideal balance of thrust and control for small craft. This power band provides ample force for rapid launch and strong headway while maintaining manageable handling for precise rescue maneuvers.
What spare parts and service support are available to BUKH engine owners to ensure long-term reliability?
A global network of specialist distributors ensures genuine spare parts and expert service are accessible for the lifespan of your installation. Support includes: worldwide availability of legacy component kits; technical guidance for maintenance and keel cooled system checks; OEM-backed repair protocols from the manufacturer.
How does the gearbox configuration on BUKH DV series engines contribute to safe and predictable maneuvering?
The integrated gearbox offers precise and immediate response to helm inputs. This direct control is vital for safe maneuvering in close quarters during high-stress recovery operations. Its predictable performance allows operators to focus on the rescue, not the engine's behavior.