Kobelt manufactures marine controls, known for their durability and precision. Kobelt controls, like the Kobelt gashendel (throttle control), and Kobelt motorbediening (engine control), are integral to the handling and performance of boats, allowing for seamless operation. These products are made with high-quality materials, ensuring long-lasting functionality in the challenging marine environment. Additionally, Kobelt offers a wide range of push-pull controls, electronic control systems, and propulsion control solutions, catering to the diverse needs of the marine and industrial sectors.
|
1-2 weeks delivery time Price incl. 19% VAT This device is designed to receive a command signal from models 7167, 7169, 7171, 7172 and 7176. The 7144, 7145 and 7148 are equipped with solenoid valves and can be activated with the 7173-K model, which will accelerate hydraulic fluid in the hydraulic steering system to maintain the desired position. This device can be located anywhere on board the vessel, even in the steering compartment, since its water resistance and non-aggressive materials will prevent water from getting close to the electronics inside.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT This device is intended for mechanical connection with baller. Its goal is to return the steering angle position for systems such as Auto Pilot, full Follow Up and Rudder control systems to the angle indicator. This device is available in up to 3 potentiometers. It is made of bronze and stainless steel and has withstood vibrations and corrosion for years.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT The 7175 rudder system will continuously monitor and indicate the position of your rudder. When changing course or maneuvering, the indicator will display this in three different colors on the panel. The system prevents accidental deviation from the course. Great indicator to always stay on track.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT The block is made entirely of bronze and stainless steel, was specially designed for the optimal position of the rudder. Equipped with a manual dimmer for backlight, internal parts are freely available, thanks to a removable plate at the bottom of the device. They are illuminated by bulbs that have a nominal service life of 30000 hours. The device is available in a 12-volt or 24-volt DC system.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT The 7181 is another addition to the steering series. This model can be used as the main electronic control of the station and is well suited for conventional or high-speed vessels. One potentiometer is used to position the rudder once. A second potentiometer can be used to show possible directions. When the device is equipped with several potentiometers, it can also be used for a catamaran with synchronized steering. Up to 4x potentiometers can be installed in the unit. The control knob can be supplied in a variety of styles. Weight: 5.5 pounds (2.5 kg)
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT Used in manual hydraulic steering system, installation with hydraulic pressure source is required. 7201 is designed specifically for high-quality work in autopilot. It is available with 12 or 24 DC volts. The pump itself can be used on a permanent basis, but the engine will overheat if the pump is set at a high level and relatively high pressure. The maximum current to allow the motor to operate on a non-constant basis is approximately 30 amps per 12 volts of engine and 15 amps for 24 volts. A lock valve is installed on the pump to prevent feedback in the hydraulic steering system. Both pumps and motors are equipped with ball bearings. The pump is made of silicon and bronze, with stainless steel hardware with hardened steel pistons.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT Kobelt 7201 Auto Pilot Hydraulic pump that comes with a special board. The relay on the board is capable of handling 30 amperes of current for any rotation. A fuse is provided for maximum engine load at 30. This is designed for 12 volts of engine. For 24 volts of the engine, the maximum load is 15 amps, and the fuse is installed accordingly.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT This series of disc brakes was specially designed to go along with the 5020 brake calipers, again, so that the entire system works smoothly and reliably. Due to the self-cooling system of these disks, they can be placed in the category of ultra-strong and very wear-resistant. The versatility of these disks is practically unlimited. These discs are cast with their high strength cast iron and are also available from other different materials, as desired by the customer.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT These discs are designed to match caliper 5021 through 5024 as well as model 5027. This series of vented type disks, thanks to their rib in a design that allows them to cool. Therefore, they are in a series of heavy-duty and wear-resistant. We recommend that you contact our specialists in order to choose the true correct disk option.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT These discs are designed to match the 5019 brake calipers (liquid or spring). These disks are designed for medium operating conditions, due to their internal ventilated design, they are extremely wear-resistant. They are made of cast iron.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT These brake discs are designed for medium to high operating levels. The patented design involves rapid cooling of the disks due to air fuses. This drive will perform tasks that are not possible with conventional ventilated drives. These discs are available in two different sizes. Great friction gives you more contact area with the brake pad. They have a powerful braking force.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT This caliper is designed specifically for medium and light operating conditions, and is used in almost all industries. Due to its compact and durable design, it can be installed in very small spaces, and will do its job for many years. The caliper is equipped with balancing, for uniform wear. The structure is made of bronze and stainless steel.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT The fluid pressure in this system is absolutely proportional to the braking force. An increase in pressure will increase the braking torque. All 5019 brake calipers can be used in any of hydraulic or pneumatic applications, as its "O" ring and piston design will not be damaged by hydraulic fluid. A spring drive is available with a large number of combinations, including adjustable springs, for various braking moments. The standard brake pads supplied by Kobelt are made of asbestos, and have been designed to provide a coefficient of friction of approximately 0.45 to 0.55. The lining can withstand up to 7500 ° F (400 ° C). Brake shoe bearings - removable from the brake shoe itself. This arrangement allows adjustment washers to be installed between the bearing and brake pads. Installation of adjustment gaskets between these two elements will reduce the gap between the brake pads. 5019 has a leg mount or side mount.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT The 5020 is a larger model of the 5019. However, it has a much higher downforce, and therefore fits into the environment of difficult conditions. Replaceable gaskets can be installed between brake pads to adapt to different disc thicknesses. Membrane-type fluid is used. Maximum pressure 100 psi (6.9 bar). The braking force is directly proportional to the fluid pressure in the actuator. Two pipe connections are provided on the drive. These pipe ports are common within the structure, and therefore, in most cases, only one inlet for connection is quite enough. All are made of bronze and stainless steel, which will ensure years of uninterrupted service. Kobelt developed an entire series of brake discs to go with this in the kit, due to its popularity.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT A special series of brake discs (12-30 "diameter), with super ventilation and a lot of energy capabilities, was designed to go with a 5020 brake caliper, providing almost unlimited applications in all industries for stop and brake. The force is absolutely proportional to the force of the actuator. Therefore, by changing the control pressure on the actuator, a smooth and positive response of the system is ensured. All Kobelt brakes are equipped with patented balancing links that provide equal wear on the brake pads.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT The 5021 brake caliper is very flexible due to its large area and reinforced clamp. This is the main reason why it is used in almost all industries where frequent braking and stopping are required. Patented balancing rods provide uniform wear on both brake pads. Washers can be installed between brake pads to reduce the gap between them. The maximum disk thickness is 2. The drive is equipped with two holes for supplying liquid. These ports are interconnected internally and require only one input. The maximum liquid supply is 100 psi (6.9 bar).
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT As the fluid pressure decreases, the actuator spring begins to press on the brakes. The manual screw option is available to adjust fluid pressure. To achieve different pressure forces, various springs are available. The drives are made of bronze and stainless steel hardware, together with carbon steel. Steel springs made of stainless steel are available by special order. The drive fluid pressure shall not exceed 250 psi.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT This caliper is a derivative of the 5021, where in fact the two brakes are combined into one. This doubles the clamping forces and also increases the clamping area. 5022 is a very compact caliper and is ideal for installation in a limited space. Most parts for 5022 are interchangeable with the 5021 model. The drives are equipped with two ports each. Only one port is required to connect to the management source in most applications. The maximum feed pressure to the caliper is 100 psi (6.9 bar). The bearings are detached from the brake shoe and alignment plates may be installed between the two members to reduce the clearance between the brake pads. The pusher on the air actuator also has an adjustment which can be used for the least wear of the brake pads. This will avoid excessive use of compressed air when the brake pedal is pressed.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT The spring caliper is used in cases where the pressure of the working fluid releases the brakes, and the spring starts to operate, replacing the liquid pressure. These brakes are extremely durable. It is simply not possible to maintain fluid pressure for a long period. However, the spring tension can be maintained almost indefinitely. The drives are very pressure sensitive and the brakes can be controlled smoothly. The slightest change in fluid pressure will cause a proportional change in braking force.
|
Our managers will contact you and clarify the terms of the order
| ||
|
1-2 weeks delivery time Price incl. 19% VAT This brake caliper was designed specifically for use in high torque systems. It is ideal for emergency stops and propeller shaft stops. It will work well with the standard disc series. This brake caliper is available with both air pneumatic pressure and spring version. Drives are equipped with two holes for liquid supply. These ports are shared and have only one input. Changing the control pressure on the drive will cause an absolutely proportional change in braking torque. The maximum liquid supply is 100 PSI (6.9 bar). Kobelt has developed an entire series of brake discs to match this caliper.
|
Our managers will contact you and clarify the terms of the order
| ||
What are the key features of Kobelt marine controls, and how do they contribute to the precise navigation of marine vessels?
Kobelt marine controls are renowned for their robust and precise design, utilizing state-of-the-art technology to ensure accurate navigation and control of marine vessels. The Kobelt steering system, including the Kobelt 7175 model, integrates seamlessly with other navigation components, allowing for smooth and responsive steering. Key features such as Kobelt gashendel and Kobelt motorbediening offer customizable control options, ensuring compatibility across various types of boats, contributing to their reputation for reliability and precision in the maritime industry.
In addition to steering systems, Kobelt offers a comprehensive range of marine control solutions, including pneumatic controls, push-pull controls, and rugged mechanical push-pull controls, catering to the diverse needs of maritime vessels.
In what types of boats and marine applications are Kobelt Controls most commonly utilized, and why?
Kobelt controls are most commonly utilized in commercial vessels, workboats, and luxury yachts due to their precise control and reliability. Incorporating Kobelt marine controls, such as the Kobelt 7175 model, allows these boats to achieve efficient and responsive navigation. The robust construction of Kobelt parts and the adaptability of systems like Kobelt motorbediening make them suitable for various marine applications, offering versatility and a high level of performance that meets the demanding conditions of maritime environments.
Kobelt controls systems are highly favored in the maritime industry, particularly in commercial vessels, workboats, and luxury yachts, for their exceptional precision and reliability. With Kobelt marine controls like the Kobelt 7175 model, these vessels benefit from smooth and efficient navigation, ensuring optimal performance even in challenging conditions. Kobelt's extensive range of products, including push-pull control systems, hydraulic steering helm pumps, and electronic systems for engine and propulsion, reflects their commitment to providing the widest selection of high-quality marine control solutions.
What types of Kobelt Items do you have in your catalogue?